Solution Description

one) Modest volume
2) Massive transmission torque
3) Higher efficiency
four) Reduced intake

Parameters :

Type Spec Input Energy(kw) N( enter) N(output) Output Torque Permitted axial thrust of output shaft(KN) Screw Diameter Length-diameter ratio
(N@m)
ZLYJ 112-8 5.5 800 one hundred 525 35 Ø35 25:01:00
133-8 8 800 100 764 39 Ø50 25:01:00
146-10 eleven 1000 100 1050 54 Ø55 25:01:00
173-10 18.5 900 90 1962 110 Ø65 25:01:00
200-twelve.5 thirty 1000 80 3581 a hundred and fifty five Ø75 twenty five:01:00
225-12.five 45 one thousand eighty 5371 180 Ø90 25:01:00
250-sixteen fifty five 1120 70 7503 192 Ø105 twenty five:01:00
280-16 75 960 60 7643 258 Ø110 25:01:00
315-16 eighty five 960 60 13528 287 Ø120 25:01:00
330-16 one hundred ten 960 sixty 17507 360 Ø135 25:01:00
375-sixteen 132 960 sixty 21008 390 Ø150 twenty five:01:00
395-sixteen 185 960 sixty 29442 four hundred Ø160 twenty five:01:00
420-16 a hundred and sixty 960 60 31831 430 Ø160 25:01:00
420-sixteen 220 960 sixty 31831 430 Ø170 25:01:00
450-20 213 1000 60 40640 500 Ø160/Ø170 twenty five:01:00
560-seventeen 540 a thousand fifty 84034 seven-hundred Ø200 25:01:00
630-10 540 1000 fifty 15712 770 Ø250 twenty five:01:00

ZLYJ gearbox collection are transmission units, which are specifically created for solitary-screw extruder with large precision, challenging gear area, accompany with thrust. Adopting the complex technical specs stipulated in JB/T9050.1-1999, all CZPT gearboxes are developed appropriately.
Primary Characteristics:
1. The content of gear is the high strength alloy metal, it is manufactured by carburizing, quenching (and other heat remedy), gringding method at previous. The gear is in high precison ( 6 quality ) and high hardness ( reaches HRC54-sixty two). Aside from, it characteristics minimal sound when running.
two. It contains substantial bearing capacity thrust, which is performed dependable and can endure greater axial thrust.
three. All the things are taken care of by forced lubrication and cooling system apart from quite few small specification items.
4. CZPT series gearbox is adopted by six-side processing box. Its typical installation is horizontal, but can also be altered to vertical set up in accordance to customer’s requirment.
five. Effectiveness transmission, lower sounds, long operaton time.
Bundle

Packing for screw and barrel
1) Wooden situation package deal
two) Plastic movie package
3) Suitable to transportation

Why pick us?
A> extended time knowledge and historical past
B> lengthy time nitriding treatment and heating treatment method by by itself
C>advanced Fanuk sequence CNC laptop-managed milling machines
D>depth hole drilling machine in 8meters size, which make sure the straigtnss of barrel within.
E> CAD drawing confirmation just before start off making
F> Prompt after sale support
G>Land proprietor and registration cash 25, 000, 000RMB

About us:

ZHangZhoug pinbo plastic machinery co.,ltd is located in HangZhou HangZhou city with brand of PYM(Former HangZhou yumin machine screw co.ltd since 1988). The company is specialized in making screw barrel, gearbox zlyj series, t die, filter and extruder machine. It has become one of the largest supplier of main parts in HangZhou city which 
is the basement of plastic machines. 
If there is any dilemma, you can speak to with us at any time, we will reply you as quickly as attainable!

US $400-2,600
/ Piece
|
1 Piece

(Min. Order)

###

Application: Reducer
Layout: Cycloidal
Hardness: Hardened Tooth Surface
Installation: Vertical Type
Step: Stepless
Type: Bevel Gear

###

Customization:

###

Type Spec Input Power(kw) N( enter) N(output) Output Torque Permitted axial thrust of output shaft(KN) Screw Diameter Length-diameter ratio
(N@m)
ZLYJ 112-8 5.5 800 100 525 35 Ø35 25:01:00
133-8 8 800 100 764 39 Ø50 25:01:00
146-10 11 1000 100 1050 54 Ø55 25:01:00
173-10 18.5 900 90 1962 110 Ø65 25:01:00
200-12.5 30 1000 80 3581 155 Ø75 25:01:00
225-12.5 45 1000 80 5371 180 Ø90 25:01:00
250-16 55 1120 70 7503 192 Ø105 25:01:00
280-16 75 960 60 7643 258 Ø110 25:01:00
315-16 85 960 60 13528 287 Ø120 25:01:00
330-16 110 960 60 17507 360 Ø135 25:01:00
375-16 132 960 60 21008 390 Ø150 25:01:00
395-16 185 960 60 29442 400 Ø160 25:01:00
420-16 160 960 60 31831 430 Ø160 25:01:00
420-16 220 960 60 31831 430 Ø170 25:01:00
450-20 213 1000 60 40640 500 Ø160/Ø170 25:01:00
560-17 540 1000 50 84034 700 Ø200 25:01:00
630-10 540 1000 50 103132 770 Ø250 25:01:00
US $400-2,600
/ Piece
|
1 Piece

(Min. Order)

###

Application: Reducer
Layout: Cycloidal
Hardness: Hardened Tooth Surface
Installation: Vertical Type
Step: Stepless
Type: Bevel Gear

###

Customization:

###

Type Spec Input Power(kw) N( enter) N(output) Output Torque Permitted axial thrust of output shaft(KN) Screw Diameter Length-diameter ratio
(N@m)
ZLYJ 112-8 5.5 800 100 525 35 Ø35 25:01:00
133-8 8 800 100 764 39 Ø50 25:01:00
146-10 11 1000 100 1050 54 Ø55 25:01:00
173-10 18.5 900 90 1962 110 Ø65 25:01:00
200-12.5 30 1000 80 3581 155 Ø75 25:01:00
225-12.5 45 1000 80 5371 180 Ø90 25:01:00
250-16 55 1120 70 7503 192 Ø105 25:01:00
280-16 75 960 60 7643 258 Ø110 25:01:00
315-16 85 960 60 13528 287 Ø120 25:01:00
330-16 110 960 60 17507 360 Ø135 25:01:00
375-16 132 960 60 21008 390 Ø150 25:01:00
395-16 185 960 60 29442 400 Ø160 25:01:00
420-16 160 960 60 31831 430 Ø160 25:01:00
420-16 220 960 60 31831 430 Ø170 25:01:00
450-20 213 1000 60 40640 500 Ø160/Ø170 25:01:00
560-17 540 1000 50 84034 700 Ø200 25:01:00
630-10 540 1000 50 103132 770 Ø250 25:01:00

Condition Monitoring of Cyclone Gearboxes

Whether you’re considering using a cycloidal gearbox in your home, office, or garage, you’ll want to make sure it’s made of quality material. You also want to make sure it’s designed properly, so it won’t be damaged by vibrations.helical gearbox

Planetary gearboxes

Compared to cycloidal gearboxes, planetary gearboxes are lighter and more compact, but they lack the precision and durability of the former. They are better suited for applications with high torque or speed requirements. For this reason, they are usually used in robotics applications. But, cycloidal gearboxes are still better for some applications, including those involving shock loads.
There are many factors that affect the performance of gearboxes during production. One of these is the number of teeth. In the case of planetary gearboxes, the number of teeth increases with the number of planets. The number of teeth is reduced in cycloidal gearboxes, which results in higher transmission ratios. These gearboxes also have lower breakaway torques, which means that they can be controlled more easily by the user.
A cycloid gearbox is comprised of three main parts: the ring gear, the sun gear, and the input shaft. The ring gear is fixed in the gearbox, while the sun gear transmits the rotation to the planet gears. The input shaft transfers motion to the sun gear, which in turn transmits it to the output shaft. The output shaft has a larger torque than the input shaft.
Cycloid gears have better torsional stiffness, lower wear, and lower Hertzian contact stress. However, they are also larger in size and require highly accurate manufacturing. Cycloid gears can be more difficult to manufacture than involute gears, which require large amounts of precision.
Cycloid gears can offer transmission ratios up to 300:1, and they can do this in a small package. They also have lower wear and friction, which makes them ideal for applications that require a high transmission ratio.
Cycloid gearboxes are usually equipped with a backlash of about one angular minute. This backlash provides the precision and control necessary for accurate movement. They also provide low wear and shock load capacity.
Planetary gearboxes are available in single and two-stage designs, which increase in length as stages are added. In addition to the two stages, they can be equipped with an optional output bearing, which takes up mounting space. In some applications, a third stage is also available.

Involute gears

Generally, involute gears are more complex to manufacture than cycloidal gears. For example, an involute gear tooth profile has a single curve while a cycloidal gear tooth profile has two curves. In addition, the involute curve is not within the base circle.
The involute curve is a very important component of a gear tooth and it can significantly influence the quality of contact meshing between teeth. Various works have been done on the subject, mainly focusing on the operating principles. In addition, the most important characteristic of the double-enveloping cycloid drive is its double contact lines between the meshing tooth pairs.
Cycloid gears are more powerful, less noisy, and last longer than involute gears. They also require less manufacturing operations during production. However, cycloid gears are more expensive than involute gears. Involute gears are more commonly used in linear motions while cycloid gears are used for rotary motions.
Although cycloid gears are more technically advanced, involute gears have the superior quality and are more aesthetically pleasing. Cycloid gears are used in various industrial applications such as pumps and compressors. They are also widely used in the watch industry. Nevertheless, involute gears have not yet replaced cycloid gears in the watch industry.
The cycloid disc has a number of pins around its outer edge, while an involute gear has only a single curve for the teeth. In addition, cycloid gears have a more robust and reliable design. Involute gears, on the other hand, have a cheaper rack cutter and less expensive involute teeth.
The cycloid disc’s transmission accuracy is about 98.5%, while the ring gear’s transmission accuracy is about 96%. The cycloid disc’s rotational velocity has a magnitude of 3 rad/s. A small change in the center distance does not affect the transmission accuracy. However, rotational velocity fluctuation can affect the transmission accuracy.
Cycloid gears also have the cycloid gear disc’s rotational velocity. The disc has N lobes. However, the cycloid gear disc’s transmission accuracy is still not perfect. This is because of the large rotational angles between the lobes. This also makes it difficult to manufacture.helical gearbox

Vibrations

Using modern techniques for vibration diagnostics and data-driven methods, this article presents a new approach to condition monitoring of cycloidal gearboxes. This approach focuses on detecting the root cause of gearbox failure. The article aims to provide a unified approach to gear designers.
A cycloidal gearbox is a high-precision gearbox that is used in heavy-duty machines. It has a large reduction ratio, which makes it necessary to have a very large input speed. Cycloid gears have high accuracy, but they are susceptible to vibration issues. In this article, the authors describe how a cycloidal gearbox works and how vibrations are measured. They also show how this gearbox can be used to detect faults.
The gearbox is used in positioners, multi-axis robots, and heavy-duty machines. The main characteristics of this gearbox are the high accuracy, the overload capacity, and the large reduction ratio.
There is little documentation on vibrations and condition monitoring of cycloidal gearboxes. The authors describe their approach to the problem, using a cycloidal gearbox and a testing bench. Their approach involves measuring the frequency of the gearbox with different input speeds.
The results show a good separation between the healthy and damaged states. Fault frequencies show up in the lower orders of frequencies. Faults can be detected using binning, which eliminates the need for a tachometer. In addition, binning is combined with Principal Component Analysis to determine the state of the gearbox.
This method is compared to traditional techniques. In addition, the results show how binning can be used to calculate the defect frequencies of the bearings. It is also used to determine the frequencies of the components.
The signals from the test bench are acquired using four sensors. These sensors are medium sensitivity 100 mV/g accelerometers. The signals are then processed using different signal processing techniques. The results show that the vibration signals are correlated with the internal motion of the gearbox. This information is used to identify the internal frequency of the transmission.
The frequency analysis of vibration signals is performed in cyclostationary and noncyclostationary conditions. The signals are then analyzed to determine the magnitude of the gear meshing frequency.helical gearbox

Design

Using precision gearboxes, servomotors can now control heavy loads at high speed. Unlike cam indexing devices, cycloidal gears provide extremely accurate positioning and high torque. They also provide excellent torsional stiffness and shock load capacity.
Cycloid gears are specially designed to minimize vibration at high RPM. Unlike involute gears, they are not stacked, which reduces friction and forces experienced by each tooth. In addition, cycloidal gears have lower Hertzian contact stress.
Cycloid gears are often used in multi-axis robots for positioners. They can provide transmission ratios as high as 300:1 in a compact package. They are also used in first joints in heavy machines. However, they require extremely accurate manufacturing. They are also more difficult to produce than involute gears.
A cycloidal gearbox is a type of planetary gearbox. Cycloid gears are specially designed for high gear ratios. They also have the ability to provide a large reduction ratio in a single stage. They are increasingly used in first joints in heavy machines. They are also becoming more common in robotics.
In order to achieve a large reduction ratio, the input speed of the gear must be very high. Generally, the input speed is between 500 rpm and 4500 rpm. However, in some cases, the input speed may be lower.
A cycloid is formed by rolling a rolling circle on a base circle. The ratio between the rolling circle diameter and the base circle diameter determines the shape of the cycloid. A hypocycloid is formed by rolling primarily on the inside of the base circle, while an epicycloid is formed by rolling primarily on the outside of the base circle.
Cycloid gears have a very small backlash, which minimizes the forces experienced by each tooth. These gears also have a good torsional stiffness, low friction, and shock load capacity. They also provide the best positioning accuracy.
The cycloidal gearbox was designed and built at Radom University. The design was based on three different cycloidal gears. The first pair had the external profile at the nominal dimension, while the second pair had the profile minus tolerance. The load plate had threaded screw holes arranged 15 mm away from the center.
China Extruder Gearbox for Plastic Extruder Zlyj Extruder Gearbox     small cycloidal gearboxChina Extruder Gearbox for Plastic Extruder Zlyj Extruder Gearbox     small cycloidal gearbox
editor by czh 2022-12-27